(!)Due to Microsoft's end of support for Internet Explorer 11 on 15/06/2022, this site does not support the recommended environment.

  • Penghentian penjualan kategori produk pneumatik Seri Ekonomi (E-series). Info Detail
    Notice of End of Sales for Economy Series Pneumatic Equipment Category. More information.

Linear Shafts One End Stepped, Both Ends Tapped/One End Tapped (Part Numbers)

Product Overview
Linear guide shaft is a high precision shaft product, which can be used in combination with linear bushing and other bushing products. In addition to excellent abrasion resistance, it offers a variety of alterations.
Dimensional Drawing
MISUMI Linear Guide Shafts One End Stepped Both Ends Tapped/One End Tapped Rotary Shaft Hollow Shaft Chrome Plated Bar
Specifications Overview
Type Material Hardness Surface TreatmentD (mm)L (mm)
Both ends tappedOne End Tapped
Standard
D Tolerance g7D Tolerance f8D Tolerance g7D Tolerance f8
E-SFAA-E-SFNA-S45C or GCr15High Frequency Quenched
For effective hardening layer depth, clickSurface Hardness Benchmark
S45C or GCr15 55HRC~
SUS440C or equivalent High hardness corrosion resistant steel 53HRC~
-8~3025~1498
E-SSFAA-E-SSFNA-SUS440C or equivalent High hardness corrosion resistant steel
E-PSFAA-E-PSFNA-S45C or GCr15Hard Chrome Plated
Plating hardness: HV750~
Plating thickness: 3μ or more
E-PSSFAA-E-PSSFNA-SUS440C or equivalent High hardness corrosion resistant steel
-E-PSFGA-E-PSNGAS45C-Hard Chrome Plated
Plating hardness: HV750~
Plating thickness: 10μ or more
The hardness of shaft end machined part (effective thread length + approx. 10mm) may be reduced due to the annealing effect of machining.
If there are requirements for rust prevention, please give priority to the hard-chrome plated products. Click Rust Prevention Method
For combination with linear bushing, please select high-frequency quenched products.

■Tolerance of D Part
Dg7f8
8-0.005
-0.020
-0.013
-0.035
10
12-0.006
-0.024
-0.016
-0.043
13
15
16
18
20-0.007
-0.028
-0.020
-0.053
25
30
Specification Table
Part Number1mm incrementsM (Coarse Thread)
Selection
N (Coarse Thread)
Selection
(Y)
Max.
TypeDLFP
StandardPrecision TypeStandard

One End Stepped Both Ends Tapped
(D Tolerance g7)
E-SFAA
E-SSFAA

E-PSFAA
E-PSSFAA


(D Tolerance f8)
E-PSFGA

One End Stepped One End Tapped
(D Tolerance g7)
E-SFNA
E-S
SFNA
E-PSFNA
E-PSSFNA


(D Tolerance f8)
E-PSNGA
825~99825~2982≤F≤P×463          345        800
1025~99825~3486~ 8345        3456       800
1225~119825~3486~103456        4568      1000
1325~119825~3486~1134568       4568      1000
1525~119825~3486~133456810      456810     1000
1625~119825~3486~143456810      456810     1200
2025~119825~4488~17 45681012     45681012    1200
2525~119825~4488~22 4568101216    4568101216   1200
3025~149825~4489~27  5681012162024    6810121620  1500
P dimension requires M+3≤P.
When D-P≤4 for the standard type, chamfer C on the step part is 0.2 or less.
L dimension for One End Stepped One End Tapped requires N×3≤L.
When M×2.5+4+N×2.5+4≥(Y) for the standard type, tap pilot holes may go through. When M×2+N×2≥(Y), priority is given to the effective length of threaded holes with larger diameters. In such case, Y requires Y≥M×2.5+4+N or Y≥N×2.5+4+M.
Alterations
MISUMI Linear Guide Shafts One End Stepped Both Ends Tapped/One End Tapped All Models Machining
Product Features
Feature 1: Extensively applied in various precision equipment thanks to high precision dimensional tolerance.
Feature 2: Bearing steel (S45C or GCr15) with excellent wear resistance and SUS440C or equivalent high hardness corrosion resistant steel are used for high frequency quenching, maintaining the original toughness while enhancing abrasion resistance.
Feature 3: A variety of alterations are available to accommodate different environments.
Feature 4: Usually combined with linear bushing products, achieving excellent linear guiding functionality, and less abrasion even if subject to high-speed reciprocal motion, as compared with general shaft and bushing structure.
Feature 5: The surface treatment of hard-chrome plating is available, achieving excellent anti-rust performance and HV750 plating hardness, as well as less abrasion when used in combination with high-hardness workpieces.
Precautions
MISUMI High Precision Guide Shafts Both Ends Stepped and Tapped Both Ends Stepped Selection Catalog②Reduced hardness of machined parts
 Machining is performed after quenching of base metal. The parts that may be reduced in hardness due to annealing are:
 -All threaded
 -All stepped
 -Tapped: when M≥D/2, tapped double-hole type, hard chrome plated products made of SUS440C or equivalent high hardness corrosion resistant steel
 -Adds wrench flats (SC-WSC-SX)
 -Adds screw flats (FC-WFC)
 -Adds V-grooves (VC-WVC)
 -Except for full length hardened type.
Only the shaded portion of D part is hard chrome plated.
Guide Shafts Both Ends Stepped and Tapped Both Ends Stepped Bushing MISUMI Quality Stainless Steel Material Imported from Japan
③Plating of surface treatment
 Machining is performed after surface treatment of base metal. No electroplating treatment is applied to the following parts:
 -Groove part
 -Threaded part
 -Tapped part
 -Wrench slot, V-groove, plane, cut section
 -The inside of the tube-type guide shaft may rust without hard chrome plating.
Example of Use
Standard Linear Motion MechanismFunctions of standard linear motion mechanism
①Side-by-side use of two guide shafts effectively prevents workpiece rotation
②Improved accuracy of linear motion and load capacity.
③The combination of guide shaft and linear bushing enables high-speed reciprocal motion.
④Low operational resistance, reducing the loss of workpiece.
Example Diagram
MISUMI Guide Shafts Both Ends Stepped and Tapped Both Ends Stepped Full Range of Selections
  
Product PictureFunctions of key workpieces in the mechanism
Linear guide shaft: Supporting the workpiece, combining with linear bushing to achieve guiding functionality.
For details, click Linear Guide Shafts

Linear bushing: Driving the workpiece to move on the guide shaft through the steel ball circulating structure.
For details, click Linear Bushings

Guide shaft support: Supporting and fixing the guide shaft for effective adjustment of shaft pitch and improved equipment stability.
For details, click Guide Shaft Posts

Stopper: Performing limit action for adjustment of effective stroke of mechanism
For details, click Stoppers
Direct-from-Manufacturer MISUMI Guide Shafts Both Ends Stepped and Tapped Both Ends Stepped Larger Image
Application Industries
Medical Semiconductor Electronic & Electrical
MISUMI High Frequency Quenched Shafts Both Ends Stepped and Tapped Both Ends Stepped Selection Manufacturer MISUMI Guide Shafts Both Ends Stepped and Tapped Both Ends Stepped Details Introduction Direct-from-Manufacturer Hollow Shafts for Sliding Both Ends Stepped and Tapped Both Ends Stepped MISUMI Model
Smart Phones Food Automotive
LINEAR SHAFT Rigid Shafts Both Ends Stepped and Tapped Both Ends Stepped Drawing Custom Size Hollow Shafts Both Ends Stepped and Tapped Both Ends Stepped Chrome Plated Bar Dimensional Drawing Dedicated Linear Hollow Shafts Both Ends Stepped and Tapped Both Ends Stepped Bearing Steel Stainless Steel Full Range of Models
Related Products
Linear Bushing Standard Type Straight Type Bearings With Housings T-Shaped Shaft Collars (Clamp)
Stainless Steel Rigid Shafts Chrome Plated Bar Both Ends Stepped and Tapped Both Ends Stepped Machining misumi Linear Hollow Shafts Both Ends Stepped and Tapped Both Ends Stepped Sales MISUMI Guide Shafts Introduction Linear Guide Shafts Both Ends Stepped and Tapped Both Ends Stepped Unit Mechanism Design Selection
Typical Model: LMU6 Typical Model: BGHFS6000ZZ-30 Typical Model: PSCS10-10
Advantages: High quality, affordable price, short delivery time Advantages: Full range, high precision and high quality Advantages: Matching shaft products, full range
Related Documents
For anti-rust performance of metal materials and surface treatment, click Anti-Rust Performance Table.

Part Number 

CAD Data download and 3D preview are not available because the part number has not yet been determined.

  • *In order to open the CAD Data download and 3D preview screen, the part number must be fixed.
  • Please confirm the part number from "Specification / Dimension"on the left side, and then perform the CAD Data Download / 3D Preview operation.
Loading...
Part Number
Part NumberMinimum order quantityVolume DiscountDays to ShipEnd Shape (Left) Material Heat Treatment Surface Treatment Shaft Dia. D
(Ø)
Length L
(mm)
Shaft Fit Tolerance M
(mm)
MD F
(mm)
N
(mm)
ND Changes tapped thread to fine one [NSC]
(mm)
P
(mm)

Loading...

  1. 1

Basic Information

Basic Shape One End Stepped End Shape (Right) Tapped Shaft End Perpendicularity Perpendicularity (0.2)
Precision Standard

Tech Support